Italian (Italy)English (United Kingdom)

Main Menù

Indice Articolo
PA 3x GI7B
Chassis
Electric Diagram
Power Check
Lab and Instruments
Tutte le pagine

                                         

Hello and 73 are described below my amplifier HF equip three GI7B the project to start by
 browsing the web. I see cites yu1aw without which this project will never be successful
 electronics business.
I do not know the characteristics of the lamps and Small tricks I do not know
Then I quote visit our friend JH0WJF consultant to the article I decide to start with the chassis.








Then begin the mechanical difficulties it is indeed the greatest difficulty HF amps are the mechanical
 strength because of the student temperature, ventilation, vibration we must not forget that there are equal filaments vibration breaks .I start with the greatest courage as you know mounts the simplest triodes are a cause of mounting since the first mechanical support lamp is simply a hole diameter of the grid lamp.
But still the problem of ventilation but there is not enough progress for the moment.
After pierced and set three lamps seen here is the three beautiful girls hi as planned I also set the self
 shock and bypass for the high-voltage.
You'll see the trait that determines the separation of high-voltage compartment
below is the patterns published on the web by JH0WJF




After watching this mounting quite simple but very functional I launch area has a small modification
 assembly has the base was scheduled for GI6B in absolute months are identical but powerful
Here patterns bitter modification only in the polarization of cathodes





The transistor used is simply a tip36 and zener diode and 41 volts that it allows a good polarization
of three tubes.
Not finding tubes ferrites for shock filament I realize ca with a torus here is the photo
I realize ten spires then split a can of Bakelite to fix ca in the lower compartment cathodes you will
notice the copper foil for putting as mass of decoupling capacitors and pass by.
 The cathodes are surrounded by a collar of copper to facilitate welding because this place has the gold cathode operation and raise the temperature why it is imperative to make the paste and shake for the
 vibration and temperature
The lamps were placed in a single filament for two days without the high voltage to run and then been here about ten hours with cathode polarization, tension filament, and finally the high voltage a thousand volts
 that it finally accustom lamps a function because they are surplus of the Russian army which we do not know the origin and date of manufacture
Attention handling this very important and we must make it absolutely.
To feed the filaments of lamps I chose a power supply switcher 12 will 13v adjustable soft START which to start slowly to protect lamps
Then the circuit 'entry is a classic that the same assembly that our friend JH0WJF
Here is a small glimpse of mounting input circuit that allows to adapt the impedance for a transceiver.
 This is a good compromise for use tx trade with this system filter is eliminated at the same time the
 harmonic s
An important issue is clean while the band six meters is not often overloads.



 
Then we will move symbol output circuit which is very simple to have calculated the fierce resistance
of the three lamps
About 1200 of 1.2 ohms k for the three lamps to apply the law ohms during tests here is what I have
seen .Using my mfj 259 on the frequency indicate I can pay my impedance plate in very good condition
Of course this test done on my offices in the absence of any tension attention voltage 3200 v very
 dangerous and you may kill
I advise you to be very careful unload the capacitor thereafter and short-circuit the two terminal + and - to avoid a violent shock.

I recommend you not to play with the high voltage that you are not a specialist







Here it is done now that my circuit is ready we will begin assembling
Here is the dangerous part of the amplifier HF the high voltage
 Here is the high-voltage generator for testing before the start
A small test vacuum with a probe divide by 10 manufactured by f1btm
below are the measuring instruments and IP ig





Here is almost finished assembling you remarque the capacitor plate manufacturing house also.
Yes almost finished.



Here's my little lab


Good luck and good achievement for any questions.  A very soon

http://fr.youtube.com/watch?v=S5gh6qdklOc
http://fr.youtube.com/watch?v=6NSka4xEb1A
http://fr.youtube.com/watch?v=pssexobKu_8

Excuser bad translation



Questo indirizzo e-mail è protetto dallo spam bot, abilitare Javascript per vederlo


Yes  almost finished




 
Copyright © 2018 SIXITALIA.org. Tutti i diritti riservati.
Joomla! è un software libero rilasciato sotto licenza GNU/GPL.